The Reese Carrier # 63155 that you referenced is 47 inches wide and should sit lower than the taillights of your vehicle (most likely). Mainly due to the width of this carrier it shouldn't interfere at all with the visibility of the taillights. You can measure the distance between your taillights to be certain. This carrier should sit lower and be too narrow to cause issue with that. Also, most likely the cameras that would take a picture of your license plate would be up above and the... view full answer...
Installing the Draw Tite trailer hitch part # 76128 on your 2018 Honda CR-V would have no affect on the backup camera of your vehicle or the side hazard warning system. I attached an install video for this hitch for you to check out as well.
For trailer wiring you'd then want the part # 118741 which is a confirmed fit.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one... view full answer...
Like you said, there are no restrictions for Draw-Tite trailer hitch # 75940 on a 2016 Audi Q5 models with back up camera and parking sensors. It is listed by Draw-Tite as a fit for all models of the 2016 Q5. The only note on it is that on models that have the back up camera may require fascia trimming for the hitch receiver tube. I have included a picture from the instructions showing the trimming location.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900.... view full answer...
Starting with the backup camera, I highly recommend the Rear View Safety Backup Camera System # RVS-776614-213. This particular system includes two different cameras, one for the rear of your truck and one with infrared for the rear of your trailer. The 7 inch TFT digital LCD color monitor will give you a clear picture of what is behind you so you can easily avoid stumps and other obstacles when going in reverse. Its simple wiring connections with the quick connect/disconnect kit will allow... view full answer...
The Curt hitch part # C13128 that you referenced has been confirmed as a fit for both a 2012 and 2013 Land Rover Evoque so it would work well for you. I attached an install video for you to check out as well.
For wiring you would use # 118624. The wiring will not interfere with the operation of the camera or sensors.
To complete your towing set up I recommend the etrailer ball mount kit # 989900. It includes 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. view full answer...
The location of the backup camera on the 2016 Mazda CX-5 is high enough that if you were towing a trailer you would see it but it would not be totally obstructed by the trailer behind the vehicle. All of the hitches will install in the same place so there wouldn't be a single option that would change the viewing angle.
The hitch I recommend though is the Draw Tite part # 76138 which is a confirmed fit. For trailer wiring you want the part # 118563 which is a custom fit. I attached an install... view full answer...
On your 2011 Audi Q5, models that have the backup camera could have a slightly different fascia that apparently could hang down a little further requiring a little bit of trimming around the square part of the trailer hitch # 75940. It does not affect every vehicle though (actually seems to be rare since it is not mentioned in the instructions nor had the manufacturer heard of this issue) and could be a situation where it depends on which factory the vehicle was assembled in but the details... view full answer...
For your 2012 Land Rover LR2 the Draw Tite hitch part # 75688 would be my recommendation as it fits your vehicle, does not require drilling and because it comes with a bracket for trailer wiring already welded to it.
For trailer wiring you'd then want the part # C59236 which is confirmed as a fit. Then for a bracket to bolt to the hitch wiring bracket you'd want the part # 18144.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with... view full answer...
It sounds like you are looking for the Replacement Pad Set # 8880057 for the Universal Mighty Mounts part # Y03590 that you are using to install the Yakima HandRoll part # Y04082 on the factory rack of your 2013 Toyota RAV4. view full answer...
We can't offer you anyway to turn off your back up sensors. Typically most vehicles have the ability to turn them off or mute them so that you can tow a trailer without having to hear them go off. I would be pretty surprised if BMW didn't have something similar that didn't require reprogramming.
The install harness I recommend for the ZCI part # 119250KIT. This harness does not splice into the wiring of your taillights at all and simply uses sensors that wrap around the wires so that the... view full answer...
For towing I recommend going with a Class III trailer hitch with a 2 inch receiver for your 2006 Honda Odyssey. The most popular option is Draw-Tite trailer hitch # 75270. I have linked a video showing an example installation. It is a very straight forward install so I am sure you can do it yourself at home.
Since you plan on towing I also recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4... view full answer...
Go To Results